Видео

Congrats Master, very nice techniques. Thanks for sharing your experience. ⚡️🌊🤙🏼

Como vc faz esse efeito de verde manchado dentro do balde?

I have used awlgrip for decades. When I get asked questions, I share this clip. On behalf of all newbie’s out there, thanks for providing this info!

Phone number pls ?

my one time boss , thanks allen

how long did you wait in between the 2 coats? thanks

That seems like an obscene amount of resin ending up on the floor 😮

I was thinking about using it as a subwoofer box . I want to put it in a rear side panel of my suv .

They recently changed something in this yellow tape and it is like paper - now tears instead of stretching!!!!!!! Used to be the BEST TAPE EVER!!!!

Matt, I want to thank you for your no hype, just the facts in a very detailed professional manner in your videos. 1 question. Where does the tape line go when you gloss coat the other side. Does it meet to the edge of the first line you poured? Go slightly over it? Thank you so much. Steve

what do you use for resin and tint?

Why is the reducer on the table if you don't need it?

If you want to make it to old age I highly suggest you wear protective mask

That was a fantastic video, thanks for putting together such a detailed explanation of the required steps. Very helpful.

Can you use a hvlp turbine system such as the fuji 5 stage to apply (think its 9.9 psi)? Would you still use the same needle and tip size as a conventional sprayer?

At 3:43, and 6:07 why would one use a filler that shrinks?

This video makes no sense to me. at 0:45, you say that when the primer is "thumb-print-tacky" you then apply the clear. But at 1:15 you tell us to sand the primer with 220 before applying clear. WHICH IS IT? You can't sand something that's tacky.

How is 3 and also 3 not 1:1, you explain nothing

بالسلامة يا أبا نضال.

What gun are you using to spray the texture?

I keep my boat on a trailer I want too pain the bottom of my boat which awlgrip crawl craft should I use

Yeah I got a m3 but there is NO WHERE to find what filters I need and I've tried dozens of searches. Not one fucking idiot has the information new people NEED. It's so stupid to see videos and web pages all acting as if they are talking to vets on the subject but address absolutely 0 critical things new individuals should know key words especially. I can't find an answer to what filter I need for Krylon UV-resistant clear spray even the god damn product sheet on the site says jack shit about it. We got all these products yet no way to tell wtf we need if we are new because we don't know what SPECIFICS we need to research. No product lables have helped or are lacking actual descriptions and critical key information to lock down any kind of conclusion. I know about oil based and organic but I'm not an alchemist I'm not about to invest 100 hours into searching for something that should be on the product itself andr box etc without ANY kind of ACTUAL lead on what I need. Stupid people always get to be in charge.

I'm confused. The Awlgrip website (Akzo Nobel) says that none of these products are to be applied "below the waterline". So how are so many of these RUclips folks using Awlgrip successfully on boat hulls? I'd like to use it to repaint my Crestliner but the OEM guidance to not use below waterline is concerning. What "should" we be using below the waterline?

What material do you use?

Do you polish in between hot coats and gloss coat?

So you don’t sand it after the gloss coat? That is where I am lost

Yeah, it looks like a hat.

Example is terrible

you didn't cover sizes? large medium ???

I prefer the 3M "ready to go"cause the seal is better than the individually respirator.

wow he makes it look so easy!! my first was a disaster haha!!

I just poke holes in a ziplock bag and shake it on. Comes out looking like sprayed on.

Thank you I watched multiple videos and downloaded 3ms guide to filters before I finally found your helpful video to make sense of it

Is that the flake or pearl?

This is also a video on how to make a giant nipple

I build aircraft out of blue foam Can you tell me what is the resin you use to make it go rock hard?

has anyone every put this in a mixing nozzle type sprayer?

Is the 2nd mask with the air filter keep drywall dust from lungs as well granite dust from lungs?

I just boucht the quick kick from resin research. I noticed that the viscosity is really really thick... storaged at room temp of 20⁰C. Is this normal?

Ear plugs?

Is the hot coat resin the same resin you use to laminate

What would be best to fill end reinforce inside plywood corners that will be fiberglass’s later?

Thanks for sharing your experience and work !!

Have you ever seen a Good Dry waller float a lid like an upside down blanket of snow in one swoop? It's easy just like this guy glassing!! Next level!!! nice job dude!🤣

Can I top coat with Epifanes matte finish oil based varnish?

What an absolutely useless video.

Va beach legend. These guys are true craftsman masters. Wish I had the planer skills. Really grateful to be able to have these lessons. Alohas from the 808

You truly build masterpieces I would love to have hanging on the wall

How do you check the fin cant with this method?

Whoever runs your instagram page is cussing at people talking about how they don’t spank their kids enough in reference to literally infants crying at stop lights. Not a good look and will be spreading this information across social media